PVC Waterstop Manufacturer and Supplier in Tianjin City – Specifications, Installation and Selection Guide

发布于 2026-10-15

Hengshui Zhanhe Engineering Rubber Co., Ltd. supplies pvc waterstop and related engineering rubber products to contractors, distributors and infrastructure projects worldwide. An extruded polyvinyl chloride waterstop for concrete joints, valued for chemical resistance, low cost and heat-weldable joints.

This article explains the working principle, main types, typical applications, installation points, selection criteria, standards and frequently asked questions about pvc waterstop, and is intended for engineers, purchasers and project managers.

1. What Is PVC Waterstop?

An extruded polyvinyl chloride waterstop for concrete joints, valued for chemical resistance, low cost and heat-weldable joints.

Working principle: The product works through elastic deformation and mechanical interlock to provide reliable sealing or load transfer.

2. Main Types

• Centrally embedded PVC waterstop: cast into the middle of the concrete with the deformation bulb aligned to the joint.
• Externally applied PVC waterstop: fixed to the water-facing face as an additional waterproofing layer.
• Weldable PVC waterstop: compound and profile optimised for hot-air welding on site.
• Composite PVC/rubber waterstop: corrosion-resistant PVC flanges with a rubber deformation section.

3. Typical Applications

• Perimeter joints, vertical joints and plinth joints of concrete face rockfill dams.
• Concrete joints in chemical parks, metallurgical plants, plating shops and sewage treatment structures.
• Deformation joints in tunnels, metro stations and underground car parks.
• Joints in channels, aqueducts, reservoirs and caissons.

4. Installation and Construction Points

1. Store indoors away from direct sunlight and heat sources to avoid plasticiser migration and distortion.
2. Fix with dedicated clamps or ties, aligning the bulb with the joint centre within 5 mm.
3. Weld joints with a hot-air gun and matching welding rod after trimming and preheating the ends; the bead must fuse continuously.
4. Inspect welds visually and by bending or peel sampling, and record joint checks for important areas.
5. Protect the strip during reinforcement and formwork: no foot traffic, shield from weld spatter, and keep vibrators off the strip.
6. In cold weather PVC stiffens, so handle and bend it slowly and warm it if required.

5. Selection Guide

• Confirm the design displacement, load grade and service environment before ordering.
• Select material grade according to temperature range, medium and durability requirements.
• Provide drawings or a specification list so that the manufacturer can verify sizes.

6. Standards and Quality Control

PVC Waterstop is manufactured and inspected according to applicable national and industry standards. Hengshui Zhanhe Engineering Rubber Co., Ltd. carries out batch inspection before delivery, and inspection certificates together with third-party test reports (where required by the project) can be provided.

Typical standards applied to this product family include Chinese national and transportation industry standards; equivalent international standards can be referenced upon request.

7. FAQ

Q: Can a PVC waterstop be used in potable water tanks?

A: The hygiene performance of the plasticiser and stabiliser package must be considered. For potable water structures, state the hygiene requirements in the order and obtain the relevant test report from the manufacturer, supplying the compound confirmed by the designer.

Q: How do I choose between PVC and rubber waterstops?

A: Consider three factors: chemical exposure, design joint movement and low temperature. PVC suits aggressive media; rubber suits large or repeated movement and temperatures below -20 °C; a PVC/rubber composite covers both.

Q: How much does misalignment matter?

A: Quite a lot. The bulb of a centrally embedded waterstop must sit on the joint centre, usually within 5 mm. Larger offsets tear the bulb when the joint opens or create a direct leakage path along the flange, which then requires chasing out and injection grouting.

8. Price Factors

Pricing follows the section size (width x thickness) and the compound. A common 300 x 6 mm profile is typically 20-40 RMB per metre. The price rises with each thickness step and with low-temperature or chemical-resistant formulations; welding rod and fixing clamps are usually charged separately by quantity.

Packing: standard export packing (woven bags, pallets or wooden cases). Delivery terms: EXW, FOB, CFR, CIF or DAP as agreed. Payment terms: T/T, L/C or other terms subject to negotiation.

9. Why Work With Hengshui Zhanhe Engineering Rubber Co., Ltd.

• Manufacturer based in Hengshui, Hebei — the engineering rubber industry cluster in North China, with in-house production and inspection.
• OEM and ODM supported: sizes, hardness, profiles and packaging can be customized to project or market requirements.
• Batch inspection before shipment; certificates of conformity and third-party test reports available when required.
• Technical support for selection, shop drawings and installation guidance, with export packing and worldwide logistics arrangement.

10. Contact and Quotation

For specification sheets, samples, pricing or project support, please contact Hengshui Zhanhe Engineering Rubber Co., Ltd.. Email: 150051331@qq.com · Tel/WhatsApp: +86-13833886677 · Factory: No.168, Zhangtuantuo Village, Dengzhuang Town, Taocheng District, Hengshui, Hebei, China. We reply to export enquiries within 24 hours on working days.